 |
 |
|
SYS-5015TB-10GB |
- SuperServer
5015TB-10GB (Black)
|
|
|
 |
|
CPU |
- Single LGA775
ZIF Socket
- Supports a
Quad-Core Intel® Xeon®
3000 Sequence
- Supports an
Intel® Core™2 Extreme
QX9000/QX6000 series
- Supports an
Intel® Core™2 Quad Q9000/Q6000
series
- Supports an
Intel® Core™2 Duo
E8000/E7000/E6000 series
- Supports an
Intel® Pentium® dual-core E2000
series
- Supports an
Intel® Celeron® dual-core E1000
series
- Supports an Intel® Celeron®
400 series
|
|
System Bus |
- 1600 / 1333 /
1066 / 800 MHz system bus
|
|
|
 |
|
Memory Capacity |
- Four 240-pin
DIMM sockets
- Supports up to
8 GB of unbuffered, non-ECC DDR3
1333/1066/800MHz memory (Dual
Channel) or up to 4 GB Non-ECC
1600MHz XMP DDR3 memory
|
|
Memory Type |
- DDR3
1333/1066/800MHz unbuffered,
non-ECC SDRAM, 240-pin
gold-plated DIMMs or Non-ECC
1600MHz XMP DDR3 memory
|
|
DIMM Sizes |
- 256 MB,
512 MB, 1 GB, 2 GB
|
|
Memory Voltage |
|
|
|
 |
|
Chipset |
- Intel X48
chipset
- ICH9R +
Intel® 82573V + Intel®
82573L
|
|
Serial ATA |
- Intel® ICH9R
SATA controller built-in (3
Gbps)
- RAID 0, 1, 5,
10 (Windows)
- RAID 0, 1, 10
(Linux)
|
|
IPMI |
- Support for
Intelligent Platform Management
Interface v.2.0
- IPMI 2.0 with
virtual media over LAN &
optional KVM-over-LAN support
- SIMSO Slot -
Supermicro Intelligement
Management
- (Optional:
AOC-SIMSO-HTC, AOC-SIMSO+)
-
NOTE: AOC-SIMSO+
must use Dedicated LAN for
KVM-over-LAN function
|
|
Network Controllers |
- Intel®
82598EB 10 Gigabit Ethernet
Controller with CX4
interface
- Intel®
82573V & 82573L Gigabit
Ethernet Controllers
- Supports
10BASE-T, 100BASE-TX, and
1000BASE-T, RJ45 output
|
|
VGA |
- On-board
XGI Volari Z9S (32MB)
graphics
|
|
Super I/O |
|
|
Clock Generator |
|
|
|
 |
|
Serial ATA |
- Four Serial
ATA ports (3 Gbps
performance)
- Four SATA
hard drives supported
|
|
LAN |
|
|
USB |
- Up to 8x
USB 2.0 / 1.1 compliant
ports
- 2 rear
ports + 2 internal headers +
2 Type A ports
|
|
VGA |
|
|
Serial Ports |
- 1x Fast
UART 16550 serial port
- 1x internal
header
|
|
|
 |
|
BIOS Type |
- 16Mb Flash
EEPROM with Phoenix BIOS
|
|
BIOS Features |
- Plug and
Play (PnP)
- DMI 2.3
support
- PCI 2.2
- ACPI 1.0 /
2.0 (S3 Optional)
- ACPI 1.0
(limited)
- USB
Keyboard support
- Hardware
BIOS Virus protection
|
|
 |
 |
 |
|
Form Factor |
|
|
Model |
|
|
|
 |
|
Height |
|
|
Width |
|
|
Depth |
|
|
Gross Weight |
|
|
Available Colors |
|
|
|
 |
|
Buttons |
- Power
On/Off button
- System
Reset button
|
|
LEDs |
- Power LED
- Hard drive
activity LED
- 2x Network
activity LEDs
- System
Overheat LED
|
|
|
 |
|
PCI-Express |
- 1 (x16)
PCI-e 2.0 slot (Low Profile)
|
|
|
 |
|
Hot-swap |
- 2x 3.5"
SATA Hot-swap drive bays
|
|
|
 |
|
1U SATA Backplane |
|
|
 |
|
Fans |
|
|
|
 |
|
700W / 780W AC-DC power supply
w/ PFC |
|
AC Input |
- 100-240V,
60-50Hz, 9.5-3.5Amp
|
|
+5V sb |
|
|
+12V |
- 65 Amp @
180-240Vac
- 58 Amp @
100-140Vac
|
|
|
 |
|
Software |
|
|
Power Configurations |
- ACPI / ACPM
Power Management
- Main Switch
Override Mechanism
- Keyboard Wakeup
from Soft-Off
- CPU Fan
auto-off in sleep mode
- Power-on mode
control for AC power loss
recovery
|
|
|
 |
|
CPU |
- Monitors for
CPU Cores ( +1.8V, +3.3V, +5,
±12V, +3.3V Standby, +5V
Standby, VBAT, HT, Memory,
Chipset)
- CPU Core
5-Phase-switching voltage
regulator with auto-sense from
0.3750V-1.6000V
|
|
FAN |
- Total of three
4-pin fan headers
- 3x fans with
tachometer monitoring
- Status monitor
with firmware / software speed
control
- Status monitor
for on/off control
- Low noise fan
speed control
|
|
Temperature |
- Monitoring for
CPU and chassis environment
- CPU Thermal
Trip support
- Thermal Control
for 8x Fan Connectors
- PSU I2C
temperature sensing logic
- Thermal Monitor
(TM2) Support
- PECI
|
|
LED |
- CPU / System
Overheat LED
- Suspend-state
indicator LED
|
|
|
 |
RoHS
|
|
|
Environmental Specifications |
- Operating Temperature:
10°C to 35°C (50°F to 95°F)
- Non-operating Temperature:
-40°C to 70°C (-40°F to 158°F)
- Operating Relative Humidity:
8% to 90% (non-condensing)
- Non-operating Relative Humidity:
5% to 95% (non-condensing)
|
|